Biodegradable/biocompatible ABC triblock copolymer bearing hydroxyl groups in the middle block

New biodegradable/biocompatible ABC block copolymers, poly(ethylene oxide)‐b‐poly(glycidol)‐b‐poly(L ,L ‐lactide) (PEO‐PGly‐PLLA), were synthesized. First, PEO‐b‐poly(1‐ethoxyethylglycidol)‐b‐PLLA was synthesized by a successive anionic ring‐opening copolymerization of ethylene oxide, 1‐ethoxyethylglycidyl ether, and L ,L ‐lactide initiated with potassium 2‐methoxyethanolate. In the second step, the 1‐ethoxyethyl blocking groups of 1‐ethoxyethylglycidyl ether were removed at weakly acidic conditions leaving other blocks intact. The resulting copolymers were composed of hydrophilic and hydrophobic segments joined by short polyglycidol blocks with one hydroxyl group in each monomeric unit. These hydroxyl groups may be used for further copolymer transformations. The PEO‐PGly‐PLLA copolymers with a molecular weight of PLLA blocks below 5000 were water‐soluble. Above the critical micellar concentration (ranging from 0.05 to1.0 g/L, depending on the composition of copolymer), copolymers formed macromolecular micelles with a hydrophobic PLLA core and hydrophilic PEO shell. The diameters of the micelles were about 25 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3750–3760, 2003     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

贝克曼AllegraTM21R型超高速离心机故障排除一例

贝克曼Allegra^TM 21R型超高速离心机开机后，操作面板上出现错误代码“28”，离心机不旋转。离心机的电机采用无刷感应驱动，由电机驱动电源模块BSMl0GD60DN2驱动离心机的电机。故障是由于电源模块BSMl0GD60DN2损坏引起的。采用东芝三相桥式IGBT电源模块MG25Q6ES42代替BSMl0GD60DN2，并更换已烧毁的栅极电阻后。开机试验，仪器恢复正常。     

[Na(18-C-6)]2[Cu(i-mnt)2]的合成与结构分析

研究了18-冠-6与Na2[Cu(i-mnt)2][i-mnt=异丁二腈烯二硫醇阴离子,S2CC(CN)2-2]的反应,得到的配合物[Na(18-C-6)]2[Cu(i-mnt)2](1)通过元素分析、红外光谱、X射线单晶衍射进行了结构分析.配合物为单斜晶系,空间群P2(1)/c.晶体学结构数据a=1.2819(11),b=1.1793(10),c=1.4928(13)nm,β=99.121(16)°,V=2.228(3)nm3,Z=2,Dcaled.=1.369g/cm3,F(000)=958,R1=0.0521,wR2=0.1003.1中的[Cu(i-mnt)2]基团通过配体i-mnt的氮原子与两个[Na(18-C-6)]基团中的钠原子成键,形成稳定的中性配合物.     

改进型磁绝缘线振荡器的设计和数值模拟

 综合两种现有磁绝缘线振荡器的优点，对器件进行改进，将双渐变结构、轭流片和阻抗渐变三种增大功率的机制综合考虑，利用二维半全电磁PIC程序进行数值模拟，设计了一种新的改进型磁绝缘线振荡器，当外加电压为550kV，电流为35kA左右时，在L波段获得了6GW的峰值输出功率。     

一种不等带宽光学梳状滤波器

提出了一种新型—Michelson—三面镜FabryPerot型50GHz不等带宽光学梳状滤波器设计方案,分析和模拟表明:该器件将一路信道间隔为50GHz的输入信号分离成信道间隔为100GHz的奇偶两路输出信号,其中在3dB处,奇数信道带宽大于30GHz用于10Gb/s传输,偶数信道带宽大于60GHz用于40Gb/s传输对于将来的40Gb/s系统,该器件具有优势.     

差分吸收光谱法测量大气痕量气体浓度误差分析及改善方法

差分吸收光谱技术(DOAS)中采用线性最小二乘拟合方法,用痕量气体标准差分吸收截面对测量得到的差分吸收光谱进行拟合,得出大气中痕量气体的浓度.计算结果的准确性不仅取决于光谱的测量精度,而且受标准差分吸收截面以及仪器函数和温度等诸多因素的影响.详细地分析了计算误差的产生原因,提出了用高浓度样品池得到标准吸收截面的方法,针对光谱固有结构,以及温度对标准吸收截面的影响,改进了浓度反演算法.大量的实验表明,综合运用上述方法,即便对低浓度的样气,相对测量误差也能降低到10%以下.     

Admissible slopes for monotone and convex interpolation

Summary In many applications, interpolation of experimental data exhibiting some geometric property such as nonnegativity, monotonicity or convexity is unacceptable unless the interpolant reflects these characteristics. This paper identifies admissible slopes at data points of variousC ¹ interpolants which ensure a desirable shape. We discuss this question, in turn for the following function classes commonly used for shape preserving interpolations: monotone polynomials,C ¹ monotone piecewise polynomials, convex polynomials, parametric cubic curves and rational functions.     

量子算法的NMR实现方法

量子计算机是一种以量子耦合方式进行信息处理的装置[1 ] 。原则上 ,它能利用量子相干干涉方法以比传统计算机更快的速度进行诸如大数的因式分解、未排序数据库中的数据搜索等工作[2 ] 。建造大型量子计算机的主要困难是噪音、去耦和制造工艺。一方面 ,虽然离子陷阱和光学腔实验方法大有希望 ,但这些方法都还没有成功实现过量子计算。另一方面 ,因为隔离于自然环境 ,核自旋可以成为很好的“量子比特” ,可能以非传统方式使用核磁共振 (NMR)技术实现量子计算。本文介绍一种用NMR方法实现量子计算的方法 ,该方法能够用比传统方法少的步骤解决一个纯数学问题。基于该方法的简单量子计算机使用比传统计算机使用更少的函数“调用”判断一未知函数的类别。